Notices
 

Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles
  • FarmallMan's Avatar
    04-28-2017, 09:29 AM
    FarmallMan replied to a thread Tire Fix? in How to do it..
    I think the big difference between the 6.5 and 8.5 is the width. Of course, a wider tire on the same size rim will crown up higher. I'm not really...
    2 replies | 244 view(s)
  • FarmallMan's Avatar
    04-28-2017, 09:19 AM
    Hi Paul, On the E15 (basically the same as the E12S) the original charger is hooked to the tractor's wiring with wire 2 and wire 30. Wire 2...
    1 replies | 155 view(s)
  • ahirbe's Avatar
    04-27-2017, 09:44 AM
    ahirbe replied to a thread E8M Controller in How to do it..
    Does anyone have a plain line drawing or instructions in layman's terms as to how to wire the various components in the E8M? I am very new to...
    3 replies | 267 view(s)
  • mikek's Avatar
    04-27-2017, 04:28 AM
    mikek replied to a thread E10M Question in How to do it..
    Thanks, Bush. I located it. The arm had slipped off the lever from the clutch - it seem a little fiddly! It works now - thanks.
    3 replies | 503 view(s)
  • ahirbe's Avatar
    04-25-2017, 08:23 AM
    ahirbe replied to a thread Tire Fix? in How to do it..
    I've decided to just get new tires...I found the front tires but am having trouble with finding the rear wheels with tires, I did find these...
    2 replies | 244 view(s)
  • oldskool's Avatar
    04-23-2017, 12:32 PM
    I have an E12s with a "smart charger" that has been failing for a few years now. Overcharges the fronts by a wide margin without fully charging the...
    1 replies | 155 view(s)
  • ahirbe's Avatar
    04-21-2017, 01:21 PM
    ahirbe replied to a thread E8M Controller in How to do it..
    The mower's electrical system is pretty far gone, as there was a literal rats nest under the console. I do not have a wiring diagram yet but assumed...
    3 replies | 267 view(s)
  • Bush_EGT120's Avatar
    04-20-2017, 08:55 PM
    Bush_EGT120 replied to a thread E8M Controller in How to do it..
    Any 36V controller built for Permanent Magnet motors would work. I don't remember the HP rating on that drive motor, but probably wouldn't need to be...
    3 replies | 267 view(s)
  • ahirbe's Avatar
    04-20-2017, 08:25 AM
    ahirbe started a thread E8M Controller in How to do it..
    I am looking to re wire may E8M with a new controller, does anyone have any advice on which controller would work better for this mower?
    3 replies | 267 view(s)
  • ahirbe's Avatar
    04-20-2017, 08:09 AM
    ahirbe started a thread Tire Fix? in How to do it..
    I have the original "Elec-Trak" branded tires on my E8M and I am really wanting to save them. They have significant dry rot cracks and do not hold...
    2 replies | 244 view(s)
  • 1southcarolina's Avatar
    04-04-2017, 05:52 PM
    Another thing to check is the seat switch, a terminal may have come loos or the switch goes bad. This can be an issue as well Chris C.
    3 replies | 503 view(s)
  • Bush_EGT120's Avatar
    04-02-2017, 07:58 PM
    Bush_EGT120 replied to a thread E10M Question in How to do it..
    If I remember correctly, it should be mounted on the front of the transaxle. There is a large mounting plate that bolts the transaxle to the frame,...
    3 replies | 503 view(s)
  • mikek's Avatar
    03-30-2017, 10:27 PM
    mikek started a thread E10M Question in How to do it..
    My E10M suddenly developed a startup problem. I think I have narrowed it down to the "Clutch Switch". Can anyone tell where this is located? If...
    3 replies | 503 view(s)
No More Results